- Description
- Reviews
- Shipping and Refund
Split Second controllers have been the go-to option for PI injector controllers for years. Easy to set up, and supported by almost every tuner out there.
The AIC2 additional injector controller is ideally suited to turbo and supercharged engines. It provides additional fuel without changes to the stock injectors or ECU programming. This preserves the characteristics of the stock engine under light load while providing all the necessary fuel in boost.
The AIC2 additional injector controller integrates seamlessly with the stock ECU to satisfy fuel requirements in boost. It can control either upstream or port injectors. It is especially useful on modern direct injected engines which have fuel systems that are difficult to modify. There are two internal injector drivers which can be operated from a single or independent tables. Each driver can drive up to four high-impedance injectors.
Programming is done over a USB interface with the TunerPro RT engine management software which provides real-time programming, data dashboard and data logging. Bin files contain program data. Xdf definition files configure the user interface. Adx files configure data acquisition for real-time display and logging. Example bin, xdf and adx files are available from the downloads section of splitsec.com.
Two-dimensional map tables provide precise fuel control over load and RPM. Additional tables facilitate compensation for elevation, air temperature and injector dead time. Map switching can be performed by on-board comparators or user input.
An extremely versatile tach input is compatible with most engine speed signals. User definable pre-scaler and post-scalers produce an accurate tach reading on virtually any engine. The number of injection pulses per engine cycle are selectable between one and eight.
The AIC2-6 is used in conjunction with your MAP or MAF sensors to calibrate.
Legal only for racing vehicles which may never be used upon a highway.
Specifications
Actual Product Weight: .95 lbs
Input Voltage: 12v DC
Programming Connection Type: MiniUSB - USB A cable (Included in the box)
Injector Connector Type: US CAR (EV6)
Number of Injector Connectors: 6
Wire Colors:
- BATT+ Battery positive (switched +12 V) 18 Red
- BATT- Battery negative (chassis ground) 18 Black
- SIG GND ECU signal ground 20 Black/yellow
- TACH Engine speed signal 20 Yellow/black
- VIN External load voltage input (optional) 20 Green
- IAT Air temp sensor (optional) 20 Gray
- AFR External AFR meter 20 Yellow
- MAP SW Switch to ground to select table B 20 Brown
- RELAY Low side of relay coil 20 Orange
- INJ+ (2) Injector plug positive (B+) 20 Red
- INJ- (DR1) Injector plug negative (driver 1) 20 Tan
- INJ- (DR2) Injector plug negative (driver 2) 20 Tan/Black
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need proof of purchase.
To start a return, you can contact us at palenonracing@gmail.com. If your return is accepted, we’ll send you instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at palenonracing@gmail.com.
Damages and issues
Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right.
Exceptions / non-returnable items
Certain types of items cannot be returned, Burger Motorsports does not allow returns, custom products (such as special orders or personalized items), JB4 Tuners and air filters can not be returned. We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item.
Unfortunately, we cannot accept returns on sale items or gift cards.
Exchanges
The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item.
Refunds
We will notify you once we’ve received and inspected your return, and let you know if the refund was approved or not. Certain circumstances will require a restocking fee of up to 25% at the discretion of Palenon Performance. (Examples of these circumstances include but are not limited to multiple failed delivery attempts, modified or damaged products and packaging, etc.) If approved, you’ll be automatically refunded on your original payment method. Please remember it can take some time for your bank or credit card company to process and post the refund too.
Handling
If the item is shipping from us direct, you will receive a tracking number within 1 business day. Most orders fulfilled at our warehouse will ship the same business day if ordered by 12pm MST. If the item is being drop shipped from the manufacturer, we cannot guarantee a tracking number within 1 business day. If an item is being drop shipped, we cannot guarantee the 24 hour (1 business day) processing time. A purchase of expedited shipping at checkout means that once item is ready to ship, it will ship using the upgraded shipping method. Some manufacturers require 3-5 days to process orders. Purchasing expedited shipping may speed up the processing time of your order, but we cannot make any guarantees in relation to faster processing time on the manufacturer’s end.
Cancellations
If you used a credit/debit card or PayPal to place an order and decide to cancel or return your order for any reason, a 5% merchant fee will be passed along to you (8% for Shop Pay installments). Some manufacturers can take up to 7 business days to ship out orders. If an item is out of stock we will reach out to you within 48 hours to confirm you would like to proceed with a preorder. If the item is listed as custom-built/ built to order within the description, or if the ETA or average lead time is visible on the product page at the time of ordering and you are cancelling inside of that ETA/lead time you will be charged the merchant fee. If the cancellation is outside of the time frame the merchant fee will not be charged to you for canceling.
Split Second controllers have been the go-to option for PI injector controllers for years. Easy to set up, and supported by almost every tuner out there.
The AIC2 additional injector controller is ideally suited to turbo and supercharged engines. It provides additional fuel without changes to the stock injectors or ECU programming. This preserves the characteristics of the stock engine under light load while providing all the necessary fuel in boost.
The AIC2 additional injector controller integrates seamlessly with the stock ECU to satisfy fuel requirements in boost. It can control either upstream or port injectors. It is especially useful on modern direct injected engines which have fuel systems that are difficult to modify. There are two internal injector drivers which can be operated from a single or independent tables. Each driver can drive up to four high-impedance injectors.
Programming is done over a USB interface with the TunerPro RT engine management software which provides real-time programming, data dashboard and data logging. Bin files contain program data. Xdf definition files configure the user interface. Adx files configure data acquisition for real-time display and logging. Example bin, xdf and adx files are available from the downloads section of splitsec.com.
Two-dimensional map tables provide precise fuel control over load and RPM. Additional tables facilitate compensation for elevation, air temperature and injector dead time. Map switching can be performed by on-board comparators or user input.
An extremely versatile tach input is compatible with most engine speed signals. User definable pre-scaler and post-scalers produce an accurate tach reading on virtually any engine. The number of injection pulses per engine cycle are selectable between one and eight.
The AIC2-6 is used in conjunction with your MAP or MAF sensors to calibrate.
Legal only for racing vehicles which may never be used upon a highway.
Specifications
Actual Product Weight: .95 lbs
Input Voltage: 12v DC
Programming Connection Type: MiniUSB - USB A cable (Included in the box)
Injector Connector Type: US CAR (EV6)
Number of Injector Connectors: 6
Wire Colors:
- BATT+ Battery positive (switched +12 V) 18 Red
- BATT- Battery negative (chassis ground) 18 Black
- SIG GND ECU signal ground 20 Black/yellow
- TACH Engine speed signal 20 Yellow/black
- VIN External load voltage input (optional) 20 Green
- IAT Air temp sensor (optional) 20 Gray
- AFR External AFR meter 20 Yellow
- MAP SW Switch to ground to select table B 20 Brown
- RELAY Low side of relay coil 20 Orange
- INJ+ (2) Injector plug positive (B+) 20 Red
- INJ- (DR1) Injector plug negative (driver 1) 20 Tan
- INJ- (DR2) Injector plug negative (driver 2) 20 Tan/Black
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. You’ll also need proof of purchase.
To start a return, you can contact us at palenonracing@gmail.com. If your return is accepted, we’ll send you instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at palenonracing@gmail.com.
Damages and issues
Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right.
Exceptions / non-returnable items
Certain types of items cannot be returned, Burger Motorsports does not allow returns, custom products (such as special orders or personalized items), JB4 Tuners and air filters can not be returned. We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item.
Unfortunately, we cannot accept returns on sale items or gift cards.
Exchanges
The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item.
Refunds
We will notify you once we’ve received and inspected your return, and let you know if the refund was approved or not. Certain circumstances will require a restocking fee of up to 25% at the discretion of Palenon Performance. (Examples of these circumstances include but are not limited to multiple failed delivery attempts, modified or damaged products and packaging, etc.) If approved, you’ll be automatically refunded on your original payment method. Please remember it can take some time for your bank or credit card company to process and post the refund too.
Handling
If the item is shipping from us direct, you will receive a tracking number within 1 business day. Most orders fulfilled at our warehouse will ship the same business day if ordered by 12pm MST. If the item is being drop shipped from the manufacturer, we cannot guarantee a tracking number within 1 business day. If an item is being drop shipped, we cannot guarantee the 24 hour (1 business day) processing time. A purchase of expedited shipping at checkout means that once item is ready to ship, it will ship using the upgraded shipping method. Some manufacturers require 3-5 days to process orders. Purchasing expedited shipping may speed up the processing time of your order, but we cannot make any guarantees in relation to faster processing time on the manufacturer’s end.
Cancellations
If you used a credit/debit card or PayPal to place an order and decide to cancel or return your order for any reason, a 5% merchant fee will be passed along to you (8% for Shop Pay installments). Some manufacturers can take up to 7 business days to ship out orders. If an item is out of stock we will reach out to you within 48 hours to confirm you would like to proceed with a preorder. If the item is listed as custom-built/ built to order within the description, or if the ETA or average lead time is visible on the product page at the time of ordering and you are cancelling inside of that ETA/lead time you will be charged the merchant fee. If the cancellation is outside of the time frame the merchant fee will not be charged to you for canceling.
